*Professional Tip:
Always lay out your decals flat and go over them with a squeegee or credit card after you remove them from the shipping envelope/tube and before you start the application process. This is to re-affix the transfer tape to the decal after shipping, should any separation occur. The rolling up of decals for shipping can sometimes cause separation of the transfer tape from the decal in spots, making small air pockets. Which is normal and easily fixed. A simple laying flat and giving it a once over with a credit card or other straight edge will make sure your decal's transfer tape is nice and evenly stuck before you begin the application process.

Instructions

1. Clean your destination surface. Use sope and water, let it dry and clean with isopropyl alcohol. Alternatively use a fast -drying panel wipe with silicone killer. Do not use Glass Cleaner.

2. With your decal as-is (still taped up), lay your decal (backing-side down, transfer-tape-side up) and align as you like it. It should be adhesive side down, looking like it will look after applied. Once you get it lined up how you like it...

3. Place a strip of masking-tape (vertically) down the center of the image to hold in place, over-lapping the edge onto the destination surface. Make sure the image won't move. Once fixed...

4. Pull one side of the decal (the entire decal - transfer tape, backing and all) back flat against itself, folding over the masking-tape center-line that you just placed to hold it down. Don't crease it, just "bend" it or "fold" it.

5. Using a sharp angle, start in a corner and peel away the decals backing (away from the transfer tape that is holding the vinyl image) until you get to the masking-tape-center-line you laid to hold it in place. Keeping the vinyl (on the application-tape) pinned back with your finger, cut away the removed backing along the center- placement-tape line. Careful not to scratch your surface or cut your vinyl image. Do not try and tear the paper, this will create fuzz and dust that may create bumps under the decal.

6. Using any squeegee like item (a credit card works well), begin to lay your graphic down onto your prepared surface from the masking-take center line outward. DO NOT LAY DOWN ALL AT ONCE! Hold the image at an angle above the destination-surface, and slowly, starting at the center-placement-tape-line, press down the image from the center out using the squeegee. Squeegee from the center-tape-line outward as you lay it down, taking care to no allow air bubbles to form between the vinyl and the surface.

7. Once one side is laid down, remove the center-tape-line, then remove the other half of the vinyl backing the same way as before, and repeat the process for the other side.

8. Squeegee the entire image a few times, from the center outward, each time with greater pressure, making sure that all of itis good and pressed onto the surface.

9. Once you feel it is pressed on as good as can be, begin peeling the transfer tape off using a sharp angle against itself. If the image comes off the surface (sticking to the transfer tape), simply lay back down, and squeegee as before, then try again - remember, a sharp angle works best when separating vinyl from either the backing or the tape. If the decal does not stick, the surface was not fully cleaned, and may have oils or dust. See the illustration below for additional help.

Material
Soft PVC film available both with glossy or matt surface.

Release Paper
Silicone coated paper on one side, 135 g/m², which provides excellent weed-stripping properties. For white vinyl, a light blue silicone paper is used, to form a stronger contrast to lettering.

Adhesive
Polyacrylate, permanent

Service life by specialist application (under vertical outdoor exposure, normal climate of Central Europe)

• black/ white: 5 years
• coloured: 4 years
• metalic, chrome, gold chrome : 2 years.
• Oilslick chrome: Indefinite indoor life and short term exterior life.

Thickness
(without protective paper and adhesive) 75 micron

Dimensional stability (FINAT TM 14)
Adhered to steel, no measurable shrinkage in cross direction, in length 0,4 mm max.

Temperature resistance
Adhered to aluminium, -40° C to +80° C, no variation Water resistance Adhered to aluminium, after 48h/23° C, no variation Adhesive power* (FINAT TM 1, after 24h, stainless steel) 16 N/25 mm Tensile strength (DIN EN ISO 527) Along: min. 19 MPa Across: min. 19 MPa Elongation at break (DIN EN ISO 527) Along: min. 130% Across: min. 150%

Order Production

Every decal is made to order just for you! Please allow us up to 3 business days to create and prepare your order for shipment.

During peak times (like Black Friday and Christmas) or for custom items, production may take a little longer. If your order hasn't shipped within 7 business days, please get in touch with us.

Estimated Delivery Times

Once your order ships from our workshop, you will receive a shipping confirmation email. Below are the estimated delivery times:

Please Note: All delivery times are estimates in business days (Monday - Friday, excluding public holidays).

Shipping Methods

• Standard Shipping (Letter): A budget-friendly option with limited or no tracking. Please note that this shipping method is chosen at the buyer's own risk.

• Tracked Shipping (Parcel): For complete peace of mind, we recommend this option. It includes full tracking so you can follow your order’s journey.

Customs and Taxes

• EU Customers: Since we ship from within the EU, you will not have to pay any additional customs fees or taxes.

• International Customers (UK, Norway, etc.): Your order may be subject to import duties and taxes, which are levied once a shipment reaches your country. These charges are the responsibility of the customer.

If your order has not arrived within the estimated time, please contact us, and we will be happy to assist you.